Layer 7 routing upgradeEstimated reading time: 4 minutes
The HTTP routing mesh functionality was redesigned in UCP 3.0 for greater security and flexibility. The functionality was also renamed to “layer 7 routing”, to make it easier for new users to get started.
To route traffic to your service you apply specific labels to your swarm services, describing the hostname for the service and other configurations. Things work in the same way as they did with the HTTP routing mesh, with the only difference being that you use different labels.
You don’t have to manually update your services. During the upgrade process to 3.0, UCP updates the services to start using new labels.
This article describes the upgrade process for the routing component, so that you can troubleshoot UCP and your services, in case something goes wrong with the upgrade.
If you are using the HTTP routing mesh, and start an upgrade to UCP 3.0:
- UCP starts a reconciliation process to ensure all internal components are deployed. As part of this, services using HRM labels are inspected.
- UCP creates the
com.docker.ucp.interlock.conf-<id>based on HRM configurations.
- The HRM service is removed.
ucp-interlockservice is deployed with the configuration created.
ucp-interlockservice deploys the
The only way to rollback from an upgrade is by restoring from a backup taken before the upgrade. If something goes wrong during the upgrade process, you need to troubleshoot the interlock services and your services, since the HRM service won’t be running after the upgrade.
Check that routing works
After upgrading to UCP 3.0, you should check if all swarm services are still routable.
For services using HTTP:
curl -vs http://<ucp-url>:<hrm-http-port>/ -H "Host: <service-hostname>"
For services using HTTPS:
curl -vs https://<ucp-url>:<hrm-https-port>
After the upgrade, check that you can still use the same hostnames to access the swarm services.
The ucp-interlock services are not running
After the upgrade to UCP 3.0, the following services should be running:
ucp-interlock: monitors swarm workloads configured to use layer 7 routing.
ucp-interlock-extension: Helper service that generates the configuration for the
ucp-interlock-proxy: A service that provides load balancing and proxying for swarm workloads.
To check if these services are running, use a client bundle with administrator permissions and run:
docker ps --filter "name=ucp-interlock"
- If the
ucp-interlockservice doesn’t exist or is not running, something went wrong with the reconciliation step.
- If this still doesn’t work, it’s possible that UCP is having problems creating
com.docker.ucp.interlock.conf-1, due to name conflicts. Make sure you don’t have any configuration with the same name by running:
docker config ls --filter "name=com.docker.ucp.interlock"
- If either the
ucp-interlock-proxyservices are not running, it’s possible that there are port conflicts. As a workaround re-enable the layer 7 routing configuration from the UCP settings page. Make sure the ports you choose are not being used by other services.
Workarounds and clean-up
If you have any of the problems above, disable and enable the layer 7 routing setting on the UCP settings page. This redeploys the services with their default configuration.
When doing that make sure you specify the same ports you were using for HRM, and that no other services are listening on those ports.
You should also check if the
ucp-hrm service is running. If it is, you should
stop it since it can conflict with the
Optionally remove labels
As part of the upgrade process UCP adds the labels specific to the new layer 7 routing solution.
You can update your services to remove the old HRM labels, since they won’t be used anymore.
Optionally segregate control traffic
Interlock is designed so that all the control traffic is kept separate from the application traffic.
If before upgrading you had all your applications attached to the
network, after upgrading you can update your services to start using a
dedicated network for routing that’s not shared with other services.
Learn how to use a dedicated network.
If before upgrading you had a dedicate network to route traffic to each service,
Interlock will continue using those dedicated networks. However the
ucp-interlock will be attached to each of those networks. You can update
ucp-interlock service so that it is only connected to the